ETA 23/0892 - Sistema de aislamiento térmico por el exterior DANOTHERM CERAMIC

ETA 23/0892
Sistema de aislamiento térmico por el exterior DANOTHERM CERAMIC

The External Thermal Insulation Composite System (from now on, referred to as ETICS) DANOTHERM CERAMIC is designed and installed in accordance with the manufacturer, design and installation instructions, deposited at the IETcc. It is made up on site from these components. The manufacturer is ultimately responsible for the ETICS.

DANOTHERM CERAMIC is defined as “bonded system with supplementary mechanical fixings” with is used with EPS / XPS panel. The minimum number of fasteners per square metres are 6 for EPS / XPS and an additional fixing per m2 on the glass mesh.

This ETICS comprises the following components, which are factory produced by the manufacturer or a supplier.

	Components (trade names)						Coverage Aprox ([kg/m²)	Thickness Aprox [mm]
Insulation material with associated method of fixing	Danotherm placa EPS. Insulating board of Expanded polystyrene (EPS) with CE marking (EN 13163) with supplementary mechanical fixings (minimum 6 fasteners/m²) With a water absorption, Wp ≤ 1 kg/m² (EN ISO 29767:2020)						0.8 – 4,0	40 – 200
	DANOPRENFS. Bonded Board of Extruded polystyrene (XPS) (CE marking EN 13164) with supplementary mechanical fixings (minimum 6 fasteners/m²) With a water absorption, Wp ≤ 1 kg/m² (EN ISO 29767:2020)						1,4 – 7,0	40 – 200
Adhesive	Argotec fixtherm Netzero. Minimum bonded surface: 80 % for EPS/XPS. Cement based mortar in powder requiring addition and mixing with 18,0 ± 1.0 % water						1-2 (powder/mm thickness)	3,0 – 5,0
	Argotec Fixtherm élite. Minimum bonded surface: 80 % for EPS. Cement based mortar in powder requiring addition and mixing with 18,0 ± 1.0 % water
Base coat	Argotec fixtherm Netzero. + Danotherm malla 160 FV (glass fibre mesh) Argotec Fixtherm élite +Danotherm malla 160 FV (glass fibre mesh)							3,0 – 5,0 (two hands)
Glass fibre mesh	Glass fibre mesh resistant to the alkalis.						—	≤ 1
	Characteristics			Values
	Mesh size (mm)			3 – 6
	Tensile strength (N/mm)			30 – 60
	Elongación after ageing (%)			≥ 1.5
	Mass per unit area (g/m²)			≥ 140
	Thickness (mm)			≤ 1
	Organic content			≤ 23
Adhesive for tile	Argocola élite 600 C2TES2 (EN 12004) Cement based mortar in powder requiring addition and mixing with 22,0 ± 2,% water.						6	5
Discontinuous cladding	Tiles Group I, according to EN 14411.
	Characteristics			Values
	Maximum dimensions			2400 cm²
	maximum weight			40 kg/m^2.
Grout	Arjunt universal. The thickness of the grout joint is between 3 mm to 15 mm.						0.75
Fasteners	Plastic anchors (expansion element and sleeve) for insulation material with different lengths in relation with thickness of insulation board						Remain under the manufacturer responsibility
	Fasteners	ETA n.º	Diameter Plate (mm)		Stiffness (kN/mm)	Minimum tension load (N)
	Danotherm anclaje mecánico clavo mixto acero poliamida	14/0130	60		0,9	500*
	*These values show the minimum pull out of the fastener in the weakest support (enclosed in its ETA). Other higher values appear in their ETAs.
	Other plastic fasteners can be used with CE marking (EAD 330196-00-0604, they have to have a plate dimension ≥ 60 mm diameter and Stiffness ≥ 0,9 kN/mm
Ancillary elements	Base, corners, top and window sills, and its fixing devices